header header
Vivid

Vivid G3 coming soon in April'12!

 

Vivid New Flagship G1 Giya speaker is ready for demo!

Specification

Frequency Range: 23Hz to 44kHz (30Hz - 40kHz +/- 2dB)
Sensitivity: 91dB, 6 ohm nominal, 4 ohm minimum
Power handling: 800 watts
Weight: 154lbs
Size: 67″h x 14″w x 31.5″ d

 

Vivid K1 Speaker

For ultimate performance, the K1 floor-standing model offers a similar performance to the B1 but with the potential for increased level and detail through the use of four low frequency drivers in conjunction with mid and high units in a 3 & 1/2 way system.

K1 employs a single D50 mid range driver (patent pending), between 900Hz and 4 kHz with the range beyond being handled by a D26 tweeter (patent pending). Below 900Hz the K1 uses four C125 mid-bass drivers (patent pending), two mounted on the front baffle and two mounted on the rear baffle of the cabinet. These four drivers are internally coupled in pairs via screw tensioning units for reaction cancelling. All drivers receive the same signal at frequencies below 100Hz while above this point the drive to the rear is progressively attenuated leaving only the front upper driver to operate all the way to 900Hz to ensure good vertical dispersion at crossover. Fourth order filters ensure phase coherence through both main crossover points resulting in a seamless and symmetrical polar performance.

Integral to the K1 enclosure is the stand. Made from the same cast carbon fibre reinforced polyester compound as the enclosure, the stand provides an exceptionally stable footing further guaranteed by the use of a total of five custom spikes mounted around the periphery of the base. Adjustment of the two rear spikes and that at the front sets the correct attitude while the remaining two can then be brought into contact with the floor for maximum safety.

Within each of the streamlined arms are hidden separate conduits to guide the Van den Hul® interconnecting cable away from the two internally mounted crossovers into the base. Precision machined WBT® gold plated terminals are discretely located at the rear of the base to allow a visually unobtrusive connection to the outside world.

Technical specifications

  • Configuration: 3 & 1/2 way vented cabinet
  • Cabinet material: Complex loaded carbon fibre filled polymer
  • Finish: High gloss automotive
  • Drive units
  • 26mm metal dome hf unit
  • 50mm metal dome mf unit
  • 158mm metal coned lf unit (two pairs coupled)
  • Sensitivity: 89dB/1w @1m
  • Nominal Impedance (â�¦): 6
  • Frequency range (hz): -6dB points 35 - 44,000
  • Frequency response (hz): 39 ÃÂ� 41,000 +/- 2dB on reference axis
  • Harmonic distortion: (2nd and 3 rd harmonics) < .0.5% over frequency range
  • Cross over frequencies (hz): 100, 900, 4000
  • Power handling (music program) watts rms: 600
  • Loudspeaker dimensions (H, W, D cabinet, D base) mm: 1300, 280, 450, 488
  • Net mass (kg): 56
  • Shipping dimensions (H, W, D) mm: 1420, 450, 560
  • Shipping mass (kg): 70

 

Vivid B1 Speaker

2nd smallest Vivid floor standing model is the B1 which incorporates four drivers in a 3 & 1/2 way system. B1 employs a single D50 mid range (patent pending) driver between 900Hz and 4 kHz with the range beyond being handled by a D26 tweeter (patent pending). Below 900Hz the B1 uses two C125 mid-bass drivers (patent pending), one mounted on the front baffle and one on the rear baffle of the cabinet. These two drivers are internally coupled via a screw tensioning unit for reaction cancelling. Both drivers receive the same signal at frequencies below 100Hz while above this point the drive to the rear is progressively attenuated leaving only the front driver to operate all the way to 900Hz in order to keep the distance between drivers at a minimum around crossover. Fourth order filters ensure phase coherence through both main crossover points resulting in a seamless and symmetrical polar performance.

Integral to the B1 enclosure is the stand. Made from the same carbon fibre loaded polyester compound as the enclosure, this considerable yet graceful design provides an exceptionally stable footing while not detracting from the acoustic environment surrounding the loudspeaker, thanks to the small frontal area of each arm. To further guarantee the stability of the complete system, a total of five custom spikes are mounted around the periphery of the base. Adjustment of the front and rear spikes sets the attitude while the remaining two can then be brought into contact with the floor for maximum stability.

Within each of the streamlined arms are hidden separate conduits to guide the Van den Hul® interconnecting cable away from the two internally mounted crossovers into the base. Precision machined WBT® gold plated terminals are discretely located at the rear of the base to allow a visually unobtrusive connection to the outside world.

Technical specifications

  • Configuration: 3 & 1/2 way vented cabinet
  • Cabinet material: Complex loaded carbon fibre filled polymer
  • Finish: High gloss automotive
  • Drive units:
  • 26mm metal dome high frequency unit
  • 50mm metal dome mid frequency unit
  • 158mm metal coned low frequency unit (two of coupled)
  • Sensitivity: 89dB/1w @1m
  • Nominal Impedance: 4 (â�¦)
  • Frequency range (hz): 6dB points 35 - 44,000
  • Frequency response (hz): 39 ÃÂ� 41,000 +/- 2dB on reference axis
  • Harmonic distortion: (2nd and 3 rd harmonics) < .0.5% over frequency range
  • Cross over frequencies (hz): 100, 900, 4000
  • Power handling (music program) watts rms: 300
  • Loudspeaker dimensions (H, W, D cabinet, D base) mm: 1095, 265, 375, 420
  • Net mass (kg): 38
  • Shipping dimensions (H, W, D) mm 1220, 410, 510
  • Shipping mass (kg): 50

 

Vivid V1.5 Speaker

 

 

Specifications

  • Configuration: 2 way vented cabinet
  • Cabinet material: Complex loaded carbon fibre filled polymer
  • Finish: High gloss automotive

Drive units

  • 26mm metal dome hf unit
  • 158mm metal coned lf unit

 

  • Sensitivity: 88dB/1w @1m
  • Nominal Impedance: 8ohms
  • Freq range (hz): - 6dB points 42 - 42,000
  • Freq response (hz): 42 - 39,000 +/- 2dB on reference axis
  • Harmonic distortion: < .0.5% over frequency range
  • Cross over freq (hz): 3000
  • Pwr hand watts rms: 150
  • Dimensions (H,W,D) : 1130, 255, 240mm
  • Net mass (kg): 23 each
  • Ship dimens (H,W,D): 1300, 430, 460mm
  • Ship mass pair (kg): 37 each

 







Copyright © 2017 X AUDIO.COM.SG Xaudio. All Rights Reserved. Designed by DSTHosting.com